# generated by PrusaSlicer 2.9.4 on 2026-04-13 at 02:25:48 UTC
bed_temperature = 60
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 20
compatible_printers = 
compatible_printers_condition = printer_model=~/(COREONE|COREONEMMU3|COREONEL|COREONELMMU3)/ and nozzle_diameter[0]==0.4
compatible_prints = 
compatible_prints_condition = 
cooling = 1
cooling_perimeter_transition_distance = 10
cooling_slowdown_logic = consistent_surface
custom_parameters_filament = ""
disable_fan_first_layers = 1
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.99
fan_always_on = 1
fan_below_layer_time = 100
filament_abrasive = 0
filament_colour = #FF8000
filament_cooling_final_speed = 3.5
filament_cooling_initial_speed = 10
filament_cooling_moves = 2
filament_cost = 27.99
filament_density = 1.24
filament_deretract_speed = nil
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 10.9
filament_loading_speed = 10
filament_loading_speed_start = 50
filament_max_volumetric_speed = 12
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_purge_multiplier = 81.25%
filament_ramming_parameters = "250 100 40.1613 40.3548 40.4516 40.3548 40.2581| 0.05 40.1483 0.45 40.3419 0.95 40.3419 1.45 40.3419 1.95 40.3419 2.45 40.3419 2.95 40.3419 3.45 40.3419 3.95 40.3419 4.45 40.3419 4.95 40.3419"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = nil
filament_seam_gap_distance = nil
filament_settings_id = Panchroma PLA Satin @Prusa Core One
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0%
filament_soluble = 0
filament_spool_weight = 193
filament_stamping_distance = 45
filament_stamping_loading_speed = 29
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = 0.6
filament_travel_ramping_lift = 1
filament_travel_slope = 1
filament_type = PLA
filament_unload_time = 8.9
filament_unloading_speed = 100
filament_unloading_speed_start = 100
filament_vendor = Polymaker
filament_wipe = nil
first_layer_bed_temperature = 60
first_layer_temperature = 220
full_fan_speed_layer = 3
idle_temperature = 170
inherits = Prusament PLA @COREONE
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
overhang_fan_speed_0 = 100
overhang_fan_speed_1 = 100
overhang_fan_speed_2 = 0
overhang_fan_speed_3 = 0
slowdown_below_layer_time = 15
start_filament_gcode = "{if printer_notes!~/.*(MK4IS|XLIS|MK4S|MK3.9S|COREONE).*/}\nM900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.05{elsif nozzle_diameter[filament_extruder_id]==0.25}0.14{elsif nozzle_diameter[filament_extruder_id]==0.3}0.07{elsif nozzle_diameter[filament_extruder_id]==0.35}0.06{elsif nozzle_diameter[filament_extruder_id]==0.6}0.03{elsif nozzle_diameter[filament_extruder_id]==0.5}0.035{elsif nozzle_diameter[filament_extruder_id]==0.8}0.015{else}0{endif} ; Legacy LA\n{else}\nM572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.036{elsif nozzle_diameter[filament_extruder_id]==0.5}0.025{elsif nozzle_diameter[filament_extruder_id]==0.6}0.022{elsif nozzle_diameter[filament_extruder_id]==0.8}0.014{elsif nozzle_diameter[filament_extruder_id]==0.25}0.12{elsif nozzle_diameter[filament_extruder_id]==0.3}0.08{else}0{endif} ; Pressure advance\n{endif}\n\nM142 S36 ; set heatbreak target temp"
temperature = 210