{
    "type": "filament",
    "name": "Fiberon ASA-CF08 @Bambu Lab H2C 0.4 nozzle",
    "from": "User",
    "instantiation": "true",
    "activate_air_filtration": [
        "1"
    ],
    "additional_cooling_fan_speed": [
        "0"
    ],
    "chamber_temperatures": [
        "0"
    ],
    "circle_compensation_speed": [
        "200"
    ],
    "close_fan_the_first_x_layers": [
        "3"
    ],
    "close_additional_fan_first_x_layers": [
        "3"
    ],
    "complete_print_exhaust_fan_speed": [
        "70"
    ],
    "cool_plate_temp": [
        "0"
    ],
    "cool_plate_temp_initial_layer": [
        "0"
    ],
    "counter_coef_1": [
        "0"
    ],
    "counter_coef_2": [
        "0.008"
    ],
    "counter_coef_3": [
        "-0.041"
    ],
    "counter_limit_max": [
        "0.033"
    ],
    "counter_limit_min": [
        "-0.035"
    ],
    "diameter_limit": [
        "50"
    ],
    "during_print_exhaust_fan_speed": [
        "70"
    ],
    "eng_plate_temp": [
        "100"
    ],
    "eng_plate_temp_initial_layer": [
        "100"
    ],
    "fan_cooling_layer_time": [
        "15"
    ],
    "fan_max_speed": [
        "30"
    ],
    "fan_min_speed": [
        "10"
    ],
    "filament_adaptive_volumetric_speed": [
        "0"
    ],
    "filament_extruder_compatibility": [
        "0"
    ],
    "filament_cooling_before_tower": [
        "10",
        "10"
    ],
    "filament_preheat_temperature_delta": [
        "20",
        "20"
    ],
    "filament_tower_interface_pre_extrusion_dist": [
        "10"
    ],
    "filament_tower_interface_pre_extrusion_length": [
        "0"
    ],
    "filament_tower_ironing_area": [
        "4"
    ],
    "filament_tower_interface_purge_volume": [
        "20"
    ],
    "filament_tower_interface_print_temp": [
        "-1"
    ],
    "filament_cost": [
        "20"
    ],
    "filament_density": [
        "1.09"
    ],
    "filament_dev_ams_drying_ams_limitations": [
        "1"
    ],
    "filament_dev_ams_drying_heat_distortion_temperature": [
        "100"
    ],
    "filament_dev_ams_drying_temperature": [
        "65",
        "80",
        "65",
        "80"
    ],
    "filament_dev_ams_drying_time": [
        "12",
        "8.0",
        "12",
        "8.0"
    ],
    "filament_dev_chamber_drying_bed_temperature": [
        "90.0"
    ],
    "filament_dev_chamber_drying_time": [
        "12.0"
    ],
    "filament_dev_drying_cooling_temperature": [
        "85"
    ],
    "filament_dev_drying_softening_temperature": [
        "85"
    ],
    "filament_diameter": [
        "1.75"
    ],
    "filament_extruder_variant": [
        "Direct Drive Standard",
        "Direct Drive High Flow"
    ],
    "filament_flow_ratio": [
        "0.89",
        "nil"
    ],
    "filament_flush_temp": [
        "0"
    ],
    "filament_flush_temp_fast": [
        "0"
    ],
    "filament_flush_volumetric_speed": [
        "0"
    ],
    "filament_is_support": [
        "0"
    ],
    "filament_max_volumetric_speed": [
        "16",
        "nil"
    ],
    "filament_metal_stickiness": [
        "None"
    ],
    "filament_minimal_purge_on_wipe_tower": [
        "15"
    ],
    "filament_pre_cooling_temperature": [
        "0"
    ],
    "filament_pre_cooling_temperature_nc": [
        "220",
        "220"
    ],
    "filament_prime_volume": [
        "30"
    ],
    "filament_prime_volume_nc": [
        "30"
    ],
    "filament_printable": [
        "3"
    ],
    "filament_ramming_travel_time_nc": [
        "1",
        "1"
    ],
    "filament_ramming_volumetric_speed": [
        "-1"
    ],
    "filament_ramming_volumetric_speed_nc": [
        "-1"
    ],
    "filament_retraction_length": [
        "0.4",
        "0.4"
    ],
    "filament_scarf_seam_type": [
        "none"
    ],
    "filament_settings_id": [
        "Fiberon ASA-CF08 @BBL H2C"
    ],
    "filament_shrink": [
        "100%"
    ],
    "filament_soluble": [
        "0"
    ],
    "filament_type": [
        "ASA"
    ],
    "filament_vendor": [
        "Polymaker"
    ],
    "filament_wipe": [
        "1",
        "1"
    ],
    "filament_wipe_distance": [
        "1",
        "1"
    ],
    "filament_z_hop_types": [
        "Spiral Lift",
        "Spiral Lift"
    ],
    "full_fan_speed_layer": [
        "0"
    ],
    "additional_fan_full_speed_layer": [
        "0"
    ],
    "filament_scarf_height": [
        "10%"
    ],
    "filament_scarf_gap": [
        "0%"
    ],
    "filament_scarf_length": [
        "10"
    ],
    "filament_ramming_travel_time": [
        "0",
        "0"
    ],
    "filament_retract_length_nc": [
        "14"
    ],
    "filament_enable_overhang_speed": [
        "1"
    ],
    "filament_overhang_1_4_speed": [
        "0"
    ],
    "filament_overhang_2_4_speed": [
        "50"
    ],
    "filament_overhang_3_4_speed": [
        "30"
    ],
    "filament_overhang_4_4_speed": [
        "10"
    ],
    "filament_overhang_totally_speed": [
        "10"
    ],
    "filament_bridge_speed": [
        "25"
    ],
    "filament_change_length": [
        "4"
    ],
    "filament_velocity_adaptation_factor": [
        "1"
    ],
    "hot_plate_temp": [
        "100"
    ],
    "hot_plate_temp_initial_layer": [
        "100"
    ],
    "filament_ingredients_safe": "1",
    "filament_emission_safe": "1",
    "filament_contact_safe": "1",
    "hole_coef_1": [
        "0"
    ],
    "hole_coef_2": [
        "-0.008"
    ],
    "hole_coef_3": [
        "0.23415"
    ],
    "hole_limit_max": [
        "0.22"
    ],
    "hole_limit_min": [
        "0.088"
    ],
    "impact_strength_z": [
        "4.9"
    ],
    "long_retractions_when_ec": [
        "0"
    ],
    "no_slow_down_for_cooling_on_outwalls": [
        "0"
    ],
    "nozzle_temperature": [
        "300",
        "nil"
    ],
    "nozzle_temperature_initial_layer": [
        "300",
        "nil"
    ],
    "nozzle_temperature_range_high": [
        "280"
    ],
    "nozzle_temperature_range_low": [
        "260"
    ],
    "overhang_fan_speed": [
        "80"
    ],
    "overhang_fan_threshold": [
        "25%"
    ],
    "override_process_overhang_speed": [
        "0"
    ],
    "reduce_fan_stop_start_freq": [
        "1"
    ],
    "required_nozzle_HRC": [
        "3"
    ],
    "retraction_distances_when_ec": [
        "0"
    ],
    "slow_down_for_layer_cooling": [
        "1"
    ],
    "cooling_slowdown_logic": [
        "uniform_cooling"
    ],
    "cooling_perimeter_transition_distance": [
        "10"
    ],
    "slow_down_layer_time": [
        "6"
    ],
    "slow_down_min_speed": [
        "20",
        "20"
    ],
    "supertack_plate_temp": [
        "0"
    ],
    "supertack_plate_temp_initial_layer": [
        "0"
    ],
    "temperature_vitrification": [
        "110.8"
    ],
    "textured_plate_temp": [
        "100"
    ],
    "textured_plate_temp_initial_layer": [
        "100"
    ],
    "volumetric_speed_coefficients": [
        "0 0 0 0 0 0"
    ],
    "compatible_printers": [
        "Bambu Lab H2C 0.4 nozzle"
    ],
    "filament_start_gcode": [
        "; filament start gcode\n"
    ],
    "filament_end_gcode": [
        "; filament end gcode \n"
    ],
    "filament_adhesiveness_category": [
        "200"
    ],
    "filament_id": "PMAS01",
    "description": " ",
    "setting_id": "GFSB98_17",
    "first_x_layer_fan_speed": [
        "0"
    ],
    "filament_change_length_nc": [
        "4"
    ],
    "include": [
        "fdm_filament_template_direct_dual"
    ],
    "version": "2.6.0.3",
    "idle_temperature": [
        "0"
    ]
}