# generated by PrusaSlicer 2.9.4 on 2026-05-15 at 05:22:53 UTC
bed_temperature = 100
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = 
compatible_printers_condition = printer_model=~/(COREONE|COREONEOAK|COREONEMMU3|COREONEL|COREONELMMU3)/ and nozzle_diameter[0]!=0.8 and nozzle_diameter[0]!=0.6 and ! nozzle_high_flow[0]
compatible_prints = 
compatible_prints_condition = 
cooling = 1
cooling_perimeter_transition_distance = 10
cooling_slowdown_logic = consistent_surface
custom_parameters_filament = ""
disable_fan_first_layers = 4
enable_dynamic_fan_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1.02
fan_always_on = 0
fan_below_layer_time = 20
filament_abrasive = 0
filament_colour = #FFF2EC
filament_cooling_final_speed = 2.5
filament_cooling_initial_speed = 5
filament_cooling_moves = 3
filament_cost = 35.28
filament_density = 1.09
filament_deretract_speed = nil
filament_diameter = 1.75
filament_infill_max_crossing_speed = 140
filament_infill_max_speed = 0
filament_load_time = 10.9
filament_loading_speed = 10
filament_loading_speed_start = 50
filament_max_volumetric_speed = 12
filament_minimal_purge_on_wipe_tower = 35
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_purge_multiplier = 100%
filament_ramming_parameters = "250 100 42.4194 42.4194 42.4194 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = nil
filament_seam_gap_distance = nil
filament_settings_id = Fiberon ASA-CF08 @Prusa Core One
filament_shrinkage_compensation_xy = 0.22%
filament_shrinkage_compensation_z = 0.22%
filament_soluble = 0
filament_spool_weight = 278
filament_stamping_distance = 45
filament_stamping_loading_speed = 26.5
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = ASA
filament_unload_time = 8.9
filament_unloading_speed = 60
filament_unloading_speed_start = 60
filament_vendor = Polymaker
filament_wipe = nil
first_layer_bed_temperature = 100
first_layer_temperature = 280
full_fan_speed_layer = 0
idle_temperature = 130
inherits = Prusament ASA @COREONE
max_fan_speed = 50
min_fan_speed = 10
min_print_speed = 15
overhang_fan_speed_0 = 25
overhang_fan_speed_1 = 0
overhang_fan_speed_2 = 0
overhang_fan_speed_3 = 0
slowdown_below_layer_time = 10
start_filament_gcode = "{if printer_notes!~/.*(MK4IS|XLIS|MK4S|MK3.9S|COREONE).*/}\nM900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.06{elsif nozzle_diameter[filament_extruder_id]==0.25}0.1{elsif nozzle_diameter[filament_extruder_id]==0.3}0.06{elsif nozzle_diameter[filament_extruder_id]==0.35}0.05{elsif nozzle_diameter[filament_extruder_id]==0.5}0.03{elsif nozzle_diameter[filament_extruder_id]==0.6}0.02{elsif nozzle_diameter[filament_extruder_id]==0.8}0.01{else}0{endif} ; Legacy LA\n{else}\nM572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.02{elsif nozzle_diameter[filament_extruder_id]==0.5}0.018{elsif nozzle_diameter[filament_extruder_id]==0.6}0.012{elsif nozzle_diameter[filament_extruder_id]==0.8}0.01{elsif nozzle_diameter[filament_extruder_id]==0.25}0.09{elsif nozzle_diameter[filament_extruder_id]==0.3}0.065{else}0{endif} ; Pressure advance\n{endif}\n\nM142 S40 ; set heatbreak target temp"
temperature = 280